
Water wells
Well pump replacement
A replacement pump is not a like-for-like part swap. Sizing it to the well and the household is what decides whether you get fifteen years out of it or three.
Crews with 20+ years in the tradeLicensed & insuredOne-year warranty
No water? Call and we will tell you what it sounds like.
A well that has stopped delivering, pressure that has dropped away, or a pump that will not shut off. Call and you will get a person and a straight answer about when we can be there.
How long should a well pump last?
A properly sized submersible pump commonly runs somewhere between eight and fifteen years. The spread is wide because the things that shorten a pump’s life are all avoidable: a waterlogged pressure tank that makes it start far more often than it should, sand and sediment wearing the impellers, a pump oversized for what the well can deliver, and voltage problems at the panel.
If your last pump did not last, the useful question is why. Replacing it without answering that buys you the same result again.
Submersible or jet
Most Northeast Florida residential wells run a submersible pump, which sits down the well and pushes water up. Jet pumps sit above ground and draw water up, and they are limited by depth. Which one your property has, and which one it should have, is decided by the depth of the well and how much water the household needs.
Sizing it properly
Getting this right means matching the pump to the depth of the well, the static water level, the yield the well can sustain, and the demand from the house, including any irrigation. An undersized pump will not keep up. An oversized one draws the well down faster than it recovers, runs dry, and destroys itself doing it.
- Well depth and static water level
- Sustainable yield of the well
- Number of fixtures and simultaneous demand
- Irrigation load, which is often what an original pump was never sized for
- Available voltage and wire size to the wellhead
What we replace at the same time
When a pump comes out, the check valve, the wiring splice and the pressure switch are all accessible and all cheap relative to the cost of pulling the pump a second time. If they are near the end of their life, replacing them now is the economical decision, and we will say so rather than leaving you to find out.
What we do and do not do on wells
We service existing wells. We do not drill new ones. Pumps, pressure tanks, the switches and wiring that go with them, water testing and inspections for a sale — that is our work, and it sits under the same licence as the septic side. We do not sell or fit water treatment equipment.
Drilling a new well is a different trade with a different licence, and we will say so rather than take the job and subcontract it. If that is what you need, call anyway and we will tell you what you are looking at before you start ringing round.
Where we do this work
We handle well pump replacement across Duval, Clay, Nassau, St. Johns, Putnam, Union and Baker counties. Each area page covers the local ground conditions and which office issues the permit there.
Jacksonville · St. Augustine · Orange Park · Middleburg · Green Cove Springs · Ponte Vedra Beach · Fernandina Beach · Yulee
See every area we serve, all water well services, or who issues your permit.
Well pump replacement — questions we get asked
How long does a well pump last?
A properly sized submersible pump commonly lasts eight to fifteen years. Pumps fail early for identifiable reasons: a waterlogged pressure tank that makes the motor start far more often than it should, sand and sediment wearing the impellers, a pump oversized for the well’s actual yield, and voltage problems at the panel.
What is the difference between a submersible pump and a jet pump?
A submersible pump sits down the well and pushes water up. A jet pump sits above ground and draws water up, which limits how deep it can work. Most Northeast Florida residential wells use submersible pumps, and the right choice for a property is set by well depth and household demand.
Why did my well pump fail so soon?
The usual causes are a waterlogged pressure tank forcing the pump to start far more often than it was designed to, sediment wearing the impellers, or a pump sized larger than the well can sustain, which draws the water level down below the pump and lets it run dry. Replacing the pump without correcting the cause produces the same failure again.
Should anything else be replaced when the pump is replaced?
The check valve, the wiring splice and the pressure switch are all accessible while the pump is out and inexpensive relative to the cost of pulling the pump again later. If any of them are near the end of their life, replacing them during the same visit is the cheaper decision overall.
Related services
Wells
Well pump repair
No water at all, or pressure that comes and goes. Before anything gets replaced, the job is working out which component failed, because the wrong guess is an expensive one.
Read more →Wells
Pressure tanks
The least understood component on a well system, and the one whose failure quietly destroys the most expensive one.
Read more →Wells
Well inspections
A well inspection is usually bought against a closing date, and a closing date does not move because the well turned out to have a problem. Book it early enough that a repair is still an option.
Read more →Tell us what the system is doing.
Call and talk to someone who works on these every day, or send the details and we will come back to you.
